Specialty Coatings
Specialty coatings for long lasting protection for any project, indoors or outdoors
METALSHIELD HIGH BUILD ZINC PHOSPHITE PRIMER GREY
METALSHIELD® HIGH BUILD ZP PRIMER is an anti-corrosive shop or field primer used for the protection of steel in mild industrial and commercial environments. METALSHIELD® HIGH BUILD ZP PRIMER is high build compared with other single pack primers and contains zinc phosphate for protection against corrosion.
METALSHIELD COLD GALVANISED PRIMER
METALSHIELD® COLD GALV Primer is a single pack, zinc rich primer that incorporates a high level of finely divided zinc providing sacrificial corrosion protection to steel substrates. METALSHIELD® COLD GALV Primer is surface tolerant, touch dry in 30 minutes, and suitable to recoat in 3 hours.
LUXAPRIME ZINC PHOSPHATE LIGHT GREY
LUXAPRIME® ZP is a single pack, high build anticorrosive primer–finish that contains both zinc phosphate and micaceous iron oxide pigments. The primer is resistant to moisture and gives superior performance compared to conventional ROZP primers over power or hand tool cleaned surfaces. Relatively high builds of up to 75 microns dry film thickness are achievable in a single coat.
HI TEMP PRIMER
HI TEMP™ Uniprime is a silicone heat resistant primer. HI TEMP™ Uniprime is recommended for continuous service temperatures to 550°C. It comes with a catalyst which facilitates air drying at ambient temperature in the event that delays occur before topcoating with HI TEMP™ 400 or 600.
METALSHIELD FORD TRACTOR BLUE
METALSHIELD® PREMIUM is a UV resistant silicone modified enamel topcoat. It is high gloss, single pack, air-drying topcoat that is tintable to over 5,000 colours. METALSHIELD® PREMIUM's silicone modified resin offers advanced gloss retention and chalk resistance compared with conventional alkyd enamels.
METALSHIELD GOLDEN YELLOW
METALSHIELD® QD TOPCOAT is ideal as a coating for steel in mild and commercial environments. The preferred coating where a fast dry, easy repair and recoat finish is required. METALSHIELD® QD TOPCOAT is particularly suitable for use with METALSHIELD® QD ENAMEL PRIMER for time-critical jobs.
HI TEMP 600
HI TEMP™ 600 is a silicone high temperature coating. HI TEMP™ 600 is recommended for continuous service temperatures to 500°C. Where heat curing may be impractical, HI TEMP™ Catalyst may be used to cure HI TEMP™ 600 at ambient temperature.
LUXACHLOR CLORINATED RUBBER
LUXACHLOR® Finish is a single pack, chlorinated rubber coating that offers excellent barrier protection to a wide variety of substrates. LUXACHLOR® Finish is thermoplastic (softens on heating) and is best coated on site
Public Spaces
Public area require heavy-duty coating systems that also protect against defacement by graffiti.
LUXEPOXY WHITE PRIMER PART A & B
LUXEPOXY® 4 White Primer is suitable for a broad range of substrates such as galvanized steel, non-ferrous metals, concrete, hardwood and MDF as the primer for high performance two pack and single pack coatings. It displays a high degree of solvent, chemical and abrasion resistance.
LUXEPOXY 66 PART A & B
LUXEPOXY® 66 is a two pack epoxy blast primer. LUXEPOXY® 66 shows good drying properties at the recommended 25 microns dry film thickness and is compatible with a wide range of finishes including epoxy, chlorinated rubber, acrylic epoxy, polyurethane and conventional alkyds.
LUXEPOXY SEALER PART A & B
LUXEPOXY® Sealer has been specially designed with excellent penetrating properties which provides a means to effectively seal substrates where only minimal surface preparation is possible and in turn ensure the adhesion of subsequent coatings. Suitable for use in a wide range of environments. LUXEPOXY® Sealer can be topcoated with a wide range of coating types
DUREPON P14 ZINC PHOSPHATE LIGHT GREY PART A & B
DUREPON® P14 is a two pack epoxy primer enhanced with zinc phosphate pigment for inhibitive corrosion protection on mild steel. DUREPON® P14 can be overcoated with epoxy, polyurethane or acrylic finishes depending upon service requirements.
ZINCANODE 402 PART A & B
ZINCANODE® 402 is a two-pack epoxy zinc rich primer formulated for exceptional cathodic corrosion resistance in harsh corrosive environments. ZINCANODE® 402 is recommended for use over abrasive blast cleaned steel surfaces, especially where overcoating is required without special mist or seal coat techniques. ZINCANODE® 402 offers relatively high film builds without mud-cracking and adhesion to field weld areas cleaned by power sanding or power wire brushing.
ZINCANODE 202 PART A & B
ZINCANODE® 202 is a two pack epoxy zinc rich primer formulated with a high level of finely divided zinc metal to provide galvanic corrosion protection on steel. On curing, a hard abrasion resistant coating results, which is particularly suitable for overcoating with heavy duty finishes without the need for mist coating or the use of a tie coat. Dry film zinc levels exceed Australian Standard requirements.
DURAMAX GPE ZINC PHOSPHATE PART A & B
DUREMAX® GPE ZP has been locally developed specially for Australasian conditions using the latest epoxy technology. DUREMAX® GPE ZP is a general-purpose epoxy primer enhanced with zinc phosphate pigment for inhibitive corrosion protection on mild steel.
DURAMAX GPE PART A & B
DUREMAX® GPE is a high performance two pack epoxy protective coating locally developed specially for Australasian conditions using the latest epoxy technology.
DURAMAX GPE MI0 PART A & B
UREMAX® GPE MIO is a high performance protective coating locally developed specially for Australasian conditions using the latest epoxy technology. DUREMAX® GPE MIO is formulated with micaceous iron oxide pigment for enhanced barrier protection.
DURABILD STE GF PART A & B
DUREBILD STE® GF has been developed specifically for Australasian conditions using advanced epoxy technology and incorporates glass flake for additional barrier protection and abrasion resistance. DUREBILD® STE GF can be top-coated with a wide range of coating types and is available with a bloom-free cold cure hardener.
DURABILD STE PART A & B
DUREBILD® STE is a surface tolerant epoxy developed specifically for Australasian conditions using advanced epoxy technology. DUREBILD® STE can be top-coated with a wide range of coating types and is available with a bloom-free cold cure hardener.
DURABILD HSE PART A & B
DUREBILD® HSE is a high solids, two component epoxy with high build characteristics allowing single coat application up to 500 microns dry film thickness direct to suitably prepared mild steel and over inorganic zinc rich or epoxy anti-corrosive primers.
Protect & Decorate
Structural steel must be protected against long-term corrosion and degradation by corrosion resistant protective coatings.
Aeromaster
DULUX Professional UltraFinish Full Gloss Enamel is an interior/exterior high gloss oil-based enamel with high opacity, high film builds, outstanding durability, gloss retention and resistance to chalking.
A1 Road Marking
ROADMASTER® A1 is a single pack, fast dry road marking paint based on a durable alkyd modified chlorinated rubber resin. It may be applied to concrete and bitumen surfaces without bleeding or discolouration, providing clean lines of high visibility. ROADMASTER® A1 lines may be beaded to impart reflectance and improve night visibility by dispersing suitable glass beads immediately onto the wet paint at the rate of 2 kg of bead to every 4 litres of paint.
EPOXY THINNER
AEROMASTER® is a fast dry, water based flat paint with fast no-pick-up time and built in self chalking characteristics. AEROMASTER® can be applied to concrete or asphalt surfaces by brush, roller, airless or conventional spray equipment.
URETHANE THINNER
AEROMASTER® is a fast dry, water based flat paint with fast no-pick-up time and built in self chalking characteristics. AEROMASTER® can be applied to concrete or asphalt surfaces by brush, roller, airless or conventional spray equipment.
C.R REDUCER
AEROMASTER® is a fast dry, water based flat paint with fast no-pick-up time and built in self chalking characteristics. AEROMASTER® can be applied to concrete or asphalt surfaces by brush, roller, airless or conventional spray equipment.
MEK THINNER
AEROMASTER® is a fast dry, water based flat paint with fast no-pick-up time and built in self chalking characteristics. AEROMASTER® can be applied to concrete or asphalt surfaces by brush, roller, airless or conventional spray equipment.
ACETONE THINNER
AEROMASTER® is a fast dry, water based flat paint with fast no-pick-up time and built in self chalking characteristics. AEROMASTER® can be applied to concrete or asphalt surfaces by brush, roller, airless or conventional spray equipment.
Share
Share this article on social media